A Beginner's Guide to-Learning the Basics of Plumbing for Bathtub Installation-Installing a Bathtub
A Beginner's Guide to-Learning the Basics of Plumbing for Bathtub Installation-Installing a Bathtub
Blog Article
What're your opinions on A Step-by-Step Guide to Installing a Bathtub?
Installing a tub isn't precisely brain surgery, however it does require solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bathtub with a new one is also a reasonably tough project. If the old tub is conveniently available, the job can move rapidly; if you need to open up a wall to eliminate the old bathtub and also position the new bathtub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will require a helper to move out the old tub and embeded in the brand-new one. Make certain you have actually certified yourself for the job and also fit trying it. As opposed to hiring a service provider to take control of a halfway-completed job, it is better to think about utilizing one before you begin. Opportunities are you may require an expert plumber to make tube connections.
This short article will certainly aid you mount a new bathtub in your washroom if you have actually currently acquired a brand-new tub and also don't need to alter the plan of your previous water system pipes.
Your tools and product list need to comprise the following:
Preparing for the Installment
Firstly, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets system to avoid pressure on the bathtub.
Fit the adaptable faucet adapters to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you use all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final setting.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, then the first thing you need to do is separate the supply of water. After doing so, activate the taps to drain pipes any kind of water continuing to be in the system. The process of getting rid of the existing faucets can be quite problematic due to the restricted accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a towel prepared for the continuing to be water that will certainly originate from the pipes. When the supply pipes have been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from turning during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe connections on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Utilizing both wooden boards under its feet, place the tub in the required position. The wood boards are handy in equally spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 small factors.
The next goal is to ensure that the tub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bath tub up until the spirit level checks out level.
To mount taps, fit all-time low of the furthest flexible tap port to the proper supply pipe by making a compression join; then do the exact same for the other tap.
Activate the water and check all joints as well as brand-new pipework for leaks and also tighten them if required. Fill the bathtub as well as also examine the overflow outlet and the regular outlet for leakages.
Lastly, fix the bath paneling as described in the maker's user's manual. Tiling as well as sealing around the bathtub ought to wait until the tub has actually been utilized at the very least once as this will certainly resolve it right into its final placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin ensuring that the washing machines are in place in between the tap and the sink. Secure the tap in position with the maker given backnut. When the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The former kind ought to be connected to the tap ends first, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break a rigid seal, triggering the water to penetrate the wall in between the bathroom and the tiling, leading to difficulties with moisture and feasible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your components and installations. They are sold in tubes and cartridges, as well as are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always fill the tub with water prior to sealing, to permit the motion experienced when the bathtub remains in usage. The sealant can fracture relatively very early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently available on the marketplace. It is suggested to fit the tiles making use of waterproof or water-proof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that blog posting on Installing A Bathtub when scouting around the internet. Those who liked our post plz be sure to share it. I cherish reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Request plumbing analysis. Report this page